URL = https://mssl.ucl.ac.uk/missions/SolO/Webpages/weekly_ops_plans/SWA-operations-plan-for-LTP19-STP361-v01_early.html Start of STP361 is 2025-05-18T20:00:00Z DT = 2025-05-18T00:00:00.000 800841600.00 seconds since 2000-01-01 SCET = 1/0800841309:48841 800841309.75 SCET 290.25 seconds drift SCET DRIFT = 290.25474548339844 -------------------------------------------------------------------------------- 2025-05-18T20:05:00 WOL_start -------------------------------------------------------------------------------- 2025-05-18T23:05:00 WOL_end -------------------------------------------------------------------------------- 2025-05-19T00:05:04 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-05-19T00:05:08 AIAF100B Sensor_cadence (USE_EAS1_R, USE_EAS2_R, USE_PAS_R, IGNORE, HIGH_CADENCE, HIGH_CADENCE, HIGH_CADENCE, NOMINAL_CADENCE) ------------------- 2025-05-19T00:00:18 SCET offset = 18 -------------------------------------------------------------------------------- 2025-05-19T00:05:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 20 => OK (no check) -------------------------------------------------------------------------------- 2025-05-19T00:05:14 AIAF135A Configure_PAS_FS (0x00, 0x0A, 0x40, 0x00, 0x09, 0x01) -------------------------------------------------------------------------------- 2025-05-19T00:05:18 AIAF069A Configure_PAS_BM (0x00, 0x04, 0x5A, 0x00, 0x09, 0x24, 0x05, 0x04) -------------------------------------------------------------------------------- 2025-05-19T00:05:22 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-05-19T00:25:12 -------------------------------------------------------------------------------- 2025-05-19T00:22:25 ROLL_start_start_angle_deg:0 ERROR => PROBLEM : No PAS TC allowed before 2025-05-19T00:25:12 -------------------------------------------------------------------------------- 2025-05-19T00:27:22 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-05-19T00:29:17 AIAF061A Start_PAS_science ------------------- 2025-05-19T00:24:27 SCET offset = 267 PROBLEM => Start science offset 267 not in [20,90] or [120,190] -------------------------------------------------------------------------------- 2025-05-19T00:30:17 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 27 => OK (no check) -------------------------------------------------------------------------------- 2025-05-19T01:12:25 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-19T10:47:04 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-19T11:37:04 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-19T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 90 => OK (no check) -------------------------------------------------------------------------------- 2025-05-19T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-19T12:10:42 offset_end = 52 Estimated Calibration duration = 0:09:01.600000 offset = 52 => OK -------------------------------------------------------------------------------- 2025-05-19T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 21 => OK (no check) -------------------------------------------------------------------------------- 2025-05-20T08:37:32 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-20T09:27:32 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-20T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 90 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-05-20T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-20T12:10:42 offset_end = 52 Estimated Calibration duration = 0:09:01.600000 offset = 52 => OK -------------------------------------------------------------------------------- 2025-05-20T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 21 => OK (no check) -------------------------------------------------------------------------------- 2025-05-20T18:57:21 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-20T19:47:21 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-21T02:12:50 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-21T03:02:50 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-21T06:21:17 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-21T07:11:17 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-21T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 90 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-05-21T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-21T12:10:42 offset_end = 52 Estimated Calibration duration = 0:09:01.600000 offset = 52 => OK -------------------------------------------------------------------------------- 2025-05-21T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 21 => OK (no check) -------------------------------------------------------------------------------- 2025-05-22T05:55:00 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-22T06:45:00 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-22T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 90 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-05-22T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-22T12:10:42 offset_end = 52 Estimated Calibration duration = 0:09:01.600000 offset = 52 => OK -------------------------------------------------------------------------------- 2025-05-22T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 21 => OK (no check) -------------------------------------------------------------------------------- 2025-05-22T16:15:01 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-22T17:05:01 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-23T07:34:47 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-23T08:24:47 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-23T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 90 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-05-23T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-23T12:10:42 offset_end = 52 Estimated Calibration duration = 0:09:01.600000 offset = 52 => OK -------------------------------------------------------------------------------- 2025-05-23T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 21 => OK (no check) -------------------------------------------------------------------------------- 2025-05-23T14:54:54 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-23T15:44:54 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-23T15:58:19 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-23T16:48:19 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-23T20:18:28 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-23T21:08:28 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-24T08:42:02 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-24T09:32:02 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-24T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 90 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-05-24T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-24T12:10:42 offset_end = 52 Estimated Calibration duration = 0:09:01.600000 offset = 52 => OK -------------------------------------------------------------------------------- 2025-05-24T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 21 => OK (no check) -------------------------------------------------------------------------------- 2025-05-24T19:02:17 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-24T19:52:17 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-25T08:43:03 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-25T09:33:03 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-25T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 90 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-05-25T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-25T12:10:42 offset_end = 52 Estimated Calibration duration = 0:09:01.600000 offset = 52 => OK -------------------------------------------------------------------------------- 2025-05-25T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 21 => OK (no check) -------------------------------------------------------------------------------- 2025-05-25T19:03:23 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-25T19:53:23 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-25T23:52:50 AIAF063A Halt_science_on_PAS ------------------- 2025-05-25T23:48:00 SCET offset = 180 PROBLEM => Stop PAS science offset = 180.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-05-25T23:54:20 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-05-25T23:59:38 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-05-26T00:05:00 WOL_start -------------------------------------------------------------------------------- 2025-05-26T03:05:00 WOL_end