URL = https://mssl.ucl.ac.uk/missions/SolO/Webpages/weekly_ops_plans/SWA-operations-plan-for-LTP19-STP362-v01.html Start of STP362 is 2025-05-26T00:00:00Z DT = 2025-05-26T00:00:00.000 801532800.00 seconds since 2000-01-01 SCET = 1/0801532508:33648 801532508.51 SCET 291.49 seconds drift SCET DRIFT = 291.486572265625 -------------------------------------------------------------------------------- 2025-05-26T00:05:00 WOL_start -------------------------------------------------------------------------------- 2025-05-26T03:05:00 WOL_end -------------------------------------------------------------------------------- 2025-05-26T04:05:04 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-05-26T04:05:08 AIAF100B Sensor_cadence (USE_EAS1_R, USE_EAS2_R, USE_PAS_R, IGNORE, HIGH_CADENCE, HIGH_CADENCE, HIGH_CADENCE, NOMINAL_CADENCE) ------------------- 2025-05-26T04:00:17 SCET offset = 17 -------------------------------------------------------------------------------- 2025-05-26T04:05:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 19 => OK (no check) -------------------------------------------------------------------------------- 2025-05-26T04:05:14 AIAF135A Configure_PAS_FS (0x00, 0x0A, 0x40, 0x00, 0x09, 0x01) -------------------------------------------------------------------------------- 2025-05-26T04:05:18 AIAF069A Configure_PAS_BM (0x00, 0x04, 0x5A, 0x00, 0x09, 0x24, 0x05, 0x04) -------------------------------------------------------------------------------- 2025-05-26T04:05:22 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-05-26T04:25:12 -------------------------------------------------------------------------------- 2025-05-26T04:28:22 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-05-26T04:29:17 AIAF061A Start_PAS_science ------------------- 2025-05-26T04:24:26 SCET offset = 266 PROBLEM => Start science offset 266 not in [20,90] or [120,190] -------------------------------------------------------------------------------- 2025-05-26T04:30:17 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 26 => OK (no check) -------------------------------------------------------------------------------- 2025-05-26T08:44:00 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-26T09:34:00 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-26T12:00:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 49 => OK (no check) -------------------------------------------------------------------------------- 2025-05-26T12:02:00 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-26T12:11:01 offset_end = 70 Estimated Calibration duration = 0:09:01.600000 offset = 70 => OK -------------------------------------------------------------------------------- 2025-05-26T12:12:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 39 => OK (no check) -------------------------------------------------------------------------------- 2025-05-26T19:04:25 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-26T19:54:25 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-26T23:09:58 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-26T23:59:58 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-27T06:38:04 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-27T07:28:04 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-27T12:00:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 49 => OK (no check) -------------------------------------------------------------------------------- 2025-05-27T12:02:00 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-27T12:11:01 offset_end = 70 Estimated Calibration duration = 0:09:01.600000 offset = 70 => OK -------------------------------------------------------------------------------- 2025-05-27T12:12:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 39 => OK (no check) -------------------------------------------------------------------------------- 2025-05-28T05:54:43 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-28T06:44:43 ROLL_end_end_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-28T12:00:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 49 => OK (no check) -------------------------------------------------------------------------------- 2025-05-28T12:02:00 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-28T12:11:01 offset_end = 70 Estimated Calibration duration = 0:09:01.600000 offset = 70 => OK -------------------------------------------------------------------------------- 2025-05-28T12:12:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 39 => OK (no check) -------------------------------------------------------------------------------- 2025-05-28T16:15:18 ROLL_start_start_angle_deg:77 -------------------------------------------------------------------------------- 2025-05-28T17:05:18 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-29T08:46:36 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-29T09:36:36 ROLL_end_end_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-29T12:00:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 49 => OK (no check) -------------------------------------------------------------------------------- 2025-05-29T12:02:00 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-29T12:11:01 offset_end = 70 Estimated Calibration duration = 0:09:01.600000 offset = 70 => OK -------------------------------------------------------------------------------- 2025-05-29T12:12:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 39 => OK (no check) -------------------------------------------------------------------------------- 2025-05-29T19:07:17 ROLL_start_start_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-29T19:57:17 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-30T05:54:37 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-30T06:44:37 ROLL_end_end_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-30T12:00:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 49 => OK (no check) -------------------------------------------------------------------------------- 2025-05-30T12:02:00 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-30T12:11:01 offset_end = 70 Estimated Calibration duration = 0:09:01.600000 offset = 70 => OK -------------------------------------------------------------------------------- 2025-05-30T12:12:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 39 => OK (no check) -------------------------------------------------------------------------------- 2025-05-30T12:35:23 ROLL_start_start_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-30T13:25:23 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-30T14:37:41 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-30T15:27:41 ROLL_end_end_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-30T18:57:24 ROLL_start_start_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-30T19:47:24 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-31T04:22:40 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-05-31T05:12:40 ROLL_end_end_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-31T12:00:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 49 => OK (no check) -------------------------------------------------------------------------------- 2025-05-31T12:02:00 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-05-31T12:11:01 offset_end = 70 Estimated Calibration duration = 0:09:01.600000 offset = 70 => OK -------------------------------------------------------------------------------- 2025-05-31T12:12:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 39 => OK (no check) -------------------------------------------------------------------------------- 2025-05-31T14:43:31 ROLL_start_start_angle_deg:76 -------------------------------------------------------------------------------- 2025-05-31T15:33:31 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-01T05:54:33 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-01T06:44:33 ROLL_end_end_angle_deg:75 -------------------------------------------------------------------------------- 2025-06-01T12:00:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 49 => OK (no check) -------------------------------------------------------------------------------- 2025-06-01T12:02:00 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-01T12:11:01 offset_end = 70 Estimated Calibration duration = 0:09:01.600000 offset = 70 => OK -------------------------------------------------------------------------------- 2025-06-01T12:12:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 39 => OK (no check) -------------------------------------------------------------------------------- 2025-06-01T16:15:28 ROLL_start_start_angle_deg:75 -------------------------------------------------------------------------------- 2025-06-01T17:05:28 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-01T21:57:55 AIAF063A Halt_science_on_PAS ------------------- 2025-06-01T21:53:04 SCET offset = 184 PROBLEM => Stop PAS science offset = 184.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-06-01T21:59:40 AIAF133A Abort_the_PAS_sequencer ------------------- 2025-06-01T21:54:49 SCET offset = 289 -------------------------------------------------------------------------------- 2025-06-01T21:59:56 AIAF113A Disable_SAF_response_for_EAS_and_PAS (SASTEERING_MI) -------------------------------------------------------------------------------- 2025-06-01T22:00:00 MAINT_start_type:SA_RELUBRICATION -------------------------------------------------------------------------------- 2025-06-01T22:10:00 MAINT_end_type:SA_RELUBRICATION -------------------------------------------------------------------------------- 2025-06-01T22:10:06 AIAF112A Enable_SAF_response_for_EAS_and_PAS (SASTEERING_MI) -------------------------------------------------------------------------------- 2025-06-01T22:10:24 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 33 => OK (no check) -------------------------------------------------------------------------------- 2025-06-01T22:11:04 AIAF061A Start_PAS_science ------------------- 2025-06-01T22:06:13 SCET offset = 73 => OK -------------------------------------------------------------------------------- 2025-06-01T22:11:47 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 16 => OK (no check) -------------------------------------------------------------------------------- 2025-06-01T22:52:38 AIAF063A Halt_science_on_PAS ------------------- 2025-06-01T22:47:47 SCET offset = 167 PROBLEM => Stop PAS science offset = 167.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-06-01T22:54:20 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-06-01T22:59:38 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-01T23:05:00 WOL_start -------------------------------------------------------------------------------- 2025-06-02T02:05:00 WOL_end -------------------------------------------------------------------------------- 2025-06-02T02:15:00 TCM_start -------------------------------------------------------------------------------- 2025-06-02T07:55:00 TCM_end