URL = https://mssl.ucl.ac.uk/missions/SolO/Webpages/weekly_ops_plans/SWA-operations-plan-for-LTP20-STP365-v01_early.html Start of STP365 is 2025-06-16T00:00:00Z DT = 2025-06-16T00:00:00.000 803347200.00 seconds since 2000-01-01 SCET = 1/0803346905:10556 803346905.16 SCET 294.84 seconds drift SCET DRIFT = 294.83892822265625 -------------------------------------------------------------------------------- 2025-06-16T00:05:00 WOL_start -------------------------------------------------------------------------------- 2025-06-16T03:05:00 WOL_end -------------------------------------------------------------------------------- 2025-06-16T04:05:04 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-16T04:05:08 AIAF100B Sensor_cadence (USE_EAS1_R, USE_EAS2_R, USE_PAS_R, IGNORE, HIGH_CADENCE, HIGH_CADENCE, HIGH_CADENCE, NOMINAL_CADENCE) ------------------- 2025-06-16T04:00:14 SCET offset = 14 -------------------------------------------------------------------------------- 2025-06-16T04:05:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 16 => OK (no check) -------------------------------------------------------------------------------- 2025-06-16T04:05:14 AIAF135A Configure_PAS_FS (0x00, 0x0A, 0x40, 0x00, 0x09, 0x01) -------------------------------------------------------------------------------- 2025-06-16T04:05:18 AIAF069A Configure_PAS_BM (0x00, 0x04, 0x5A, 0x00, 0x09, 0x24, 0x05, 0x04) -------------------------------------------------------------------------------- 2025-06-16T04:05:22 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-06-16T04:25:12 -------------------------------------------------------------------------------- 2025-06-16T04:27:22 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-06-16T04:29:17 AIAF061A Start_PAS_science ------------------- 2025-06-16T04:24:23 SCET offset = 263 PROBLEM => Start science offset 263 not in [20,90] or [120,190] -------------------------------------------------------------------------------- 2025-06-16T04:30:17 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 23 => OK (no check) -------------------------------------------------------------------------------- 2025-06-16T11:05:18 ROLL_start_start_angle_deg:65 -------------------------------------------------------------------------------- 2025-06-16T11:55:18 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-16T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 86 => OK (no check) -------------------------------------------------------------------------------- 2025-06-16T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-16T12:10:42 offset_end = 48 Estimated Calibration duration = 0:09:01.600000 offset = 48 PROBLEM => Calib procedure ends at offset 48, not in [50,90] -------------------------------------------------------------------------------- 2025-06-16T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 17 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-16T14:35:33 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-16T15:25:33 ROLL_end_end_angle_deg:64 -------------------------------------------------------------------------------- 2025-06-16T20:17:21 ROLL_start_start_angle_deg:64 -------------------------------------------------------------------------------- 2025-06-16T21:07:21 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-17T02:25:06 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-17T03:15:06 ROLL_end_end_angle_deg:64 -------------------------------------------------------------------------------- 2025-06-17T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 86 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-17T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-17T12:10:42 offset_end = 48 Estimated Calibration duration = 0:09:01.600000 offset = 48 PROBLEM => Calib procedure ends at offset 48, not in [50,90] -------------------------------------------------------------------------------- 2025-06-17T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 17 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-17T13:48:28 ROLL_start_start_angle_deg:64 -------------------------------------------------------------------------------- 2025-06-17T14:38:28 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-18T02:05:44 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-18T02:55:44 ROLL_end_end_angle_deg:63 -------------------------------------------------------------------------------- 2025-06-18T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 86 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-18T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-18T12:10:42 offset_end = 48 Estimated Calibration duration = 0:09:01.600000 offset = 48 PROBLEM => Calib procedure ends at offset 48, not in [50,90] -------------------------------------------------------------------------------- 2025-06-18T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 17 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-18T16:20:52 ROLL_start_start_angle_deg:63 -------------------------------------------------------------------------------- 2025-06-18T17:10:52 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-19T04:17:08 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-19T05:07:08 ROLL_end_end_angle_deg:62 -------------------------------------------------------------------------------- 2025-06-19T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 86 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-19T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-19T12:10:42 offset_end = 48 Estimated Calibration duration = 0:09:01.600000 offset = 48 PROBLEM => Calib procedure ends at offset 48, not in [50,90] -------------------------------------------------------------------------------- 2025-06-19T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 17 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-19T19:21:12 ROLL_start_start_angle_deg:62 -------------------------------------------------------------------------------- 2025-06-19T20:11:12 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-20T04:17:08 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-20T05:07:08 ROLL_end_end_angle_deg:61 -------------------------------------------------------------------------------- 2025-06-20T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 86 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-20T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-20T12:10:42 offset_end = 48 Estimated Calibration duration = 0:09:01.600000 offset = 48 PROBLEM => Calib procedure ends at offset 48, not in [50,90] -------------------------------------------------------------------------------- 2025-06-20T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 17 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-20T19:21:11 ROLL_start_start_angle_deg:61 -------------------------------------------------------------------------------- 2025-06-20T20:11:11 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-21T04:16:57 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-21T05:06:57 ROLL_end_end_angle_deg:60 -------------------------------------------------------------------------------- 2025-06-21T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 86 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-21T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-21T12:10:42 offset_end = 48 Estimated Calibration duration = 0:09:01.600000 offset = 48 PROBLEM => Calib procedure ends at offset 48, not in [50,90] -------------------------------------------------------------------------------- 2025-06-21T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 17 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-21T12:36:35 AIAF063A Halt_science_on_PAS ------------------- 2025-06-21T12:31:41 SCET offset = 101 PROBLEM => Stop PAS science offset = 101.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-06-21T12:38:13 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-06-21T12:44:55 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-21T12:49:59 WOL_start -------------------------------------------------------------------------------- 2025-06-21T15:49:59 WOL_end -------------------------------------------------------------------------------- 2025-06-21T15:50:00 CALIB_ROLL_MAG_start -------------------------------------------------------------------------------- 2025-06-21T16:50:03 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-21T16:50:07 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-06-21T17:09:57 -------------------------------------------------------------------------------- 2025-06-21T17:12:07 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-06-21T17:13:07 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 93 => OK (no check) -------------------------------------------------------------------------------- 2025-06-21T17:13:59 AIAF061A Start_PAS_science ------------------- 2025-06-21T17:09:05 SCET offset = 245 PROBLEM => Start science offset 245 not in [20,90] or [120,190] -------------------------------------------------------------------------------- 2025-06-21T17:14:19 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 65 => OK (no check) -------------------------------------------------------------------------------- 2025-06-22T05:53:36 AIAF063A Halt_science_on_PAS ------------------- 2025-06-22T05:48:42 SCET offset = 222 PROBLEM => Stop PAS science offset = 222.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-06-22T05:55:14 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-06-22T06:01:56 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-22T06:06:40 CALIB_ROLL_MAG_end -------------------------------------------------------------------------------- 2025-06-22T06:07:00 WOL_start -------------------------------------------------------------------------------- 2025-06-22T09:07:00 WOL_end -------------------------------------------------------------------------------- 2025-06-22T10:07:04 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-22T10:07:08 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-06-22T10:26:58 -------------------------------------------------------------------------------- 2025-06-22T10:29:08 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-06-22T10:30:08 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 14 => OK (no check) -------------------------------------------------------------------------------- 2025-06-22T10:31:00 AIAF061A Start_PAS_science ------------------- 2025-06-22T10:26:06 SCET offset = 66 => OK -------------------------------------------------------------------------------- 2025-06-22T10:31:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 86 => OK (no check) -------------------------------------------------------------------------------- 2025-06-22T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 86 => OK (no check) -------------------------------------------------------------------------------- 2025-06-22T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-22T12:10:42 offset_end = 48 Estimated Calibration duration = 0:09:01.600000 offset = 48 PROBLEM => Calib procedure ends at offset 48, not in [50,90] -------------------------------------------------------------------------------- 2025-06-22T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 17 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-22T19:21:01 ROLL_start_start_angle_deg:60 -------------------------------------------------------------------------------- 2025-06-22T20:11:01 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-22T23:52:50 AIAF063A Halt_science_on_PAS ------------------- 2025-06-22T23:47:56 SCET offset = 176 PROBLEM => Stop PAS science offset = 176.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-06-22T23:54:20 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-06-22T23:59:38 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-23T00:05:00 WOL_start -------------------------------------------------------------------------------- 2025-06-23T03:05:00 WOL_end