URL = https://mssl.ucl.ac.uk/missions/SolO/Webpages/weekly_ops_plans/SWA-operations-plan-for-LTP20-STP367-v0_early.html Start of STP367 is 2025-06-30T00:00:00Z DT = 2025-06-30T00:00:00.000 804556800.00 seconds since 2000-01-01 SCET = 1/0804556502:61205 804556502.93 SCET 297.07 seconds drift SCET DRIFT = 297.0660858154297 -------------------------------------------------------------------------------- 2025-06-30T00:05:00 WOL_start -------------------------------------------------------------------------------- 2025-06-30T03:05:00 WOL_end -------------------------------------------------------------------------------- 2025-06-30T04:05:04 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-06-30T04:05:08 AIAF100B Sensor_cadence (USE_EAS1_R, USE_EAS2_R, USE_PAS_R, IGNORE, HIGH_CADENCE, HIGH_CADENCE, HIGH_CADENCE, NOMINAL_CADENCE) ------------------- 2025-06-30T04:00:11 SCET offset = 11 -------------------------------------------------------------------------------- 2025-06-30T04:05:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 13 => OK (no check) -------------------------------------------------------------------------------- 2025-06-30T04:05:14 AIAF135A Configure_PAS_FS (0x00, 0x0A, 0x40, 0x00, 0x09, 0x01) -------------------------------------------------------------------------------- 2025-06-30T04:05:18 AIAF069A Configure_PAS_BM (0x00, 0x04, 0x5A, 0x00, 0x09, 0x24, 0x05, 0x04) -------------------------------------------------------------------------------- 2025-06-30T04:05:22 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-06-30T04:25:12 -------------------------------------------------------------------------------- 2025-06-30T04:28:22 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-06-30T04:30:17 AIAF061A Start_PAS_science ------------------- 2025-06-30T04:25:20 SCET offset = 20 => OK -------------------------------------------------------------------------------- 2025-06-30T04:31:17 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 80 => OK (no check) -------------------------------------------------------------------------------- 2025-06-30T08:52:16 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-06-30T09:42:16 ROLL_end_end_angle_deg:49 -------------------------------------------------------------------------------- 2025-06-30T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 83 => OK (no check) -------------------------------------------------------------------------------- 2025-06-30T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-06-30T12:10:42 offset_end = 45 Estimated Calibration duration = 0:09:01.600000 offset = 45 PROBLEM => Calib procedure ends at offset 45, not in [50,90] -------------------------------------------------------------------------------- 2025-06-30T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 14 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-06-30T19:14:00 ROLL_start_start_angle_deg:49 -------------------------------------------------------------------------------- 2025-06-30T20:04:00 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-01T03:55:14 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-01T04:45:14 ROLL_end_end_angle_deg:48 -------------------------------------------------------------------------------- 2025-07-01T08:16:56 ROLL_start_start_angle_deg:48 -------------------------------------------------------------------------------- 2025-07-01T09:06:56 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-01T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 83 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-01T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-01T12:10:42 offset_end = 45 Estimated Calibration duration = 0:09:01.600000 offset = 45 PROBLEM => Calib procedure ends at offset 45, not in [50,90] -------------------------------------------------------------------------------- 2025-07-01T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 14 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-01T12:56:54 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-01T13:46:54 ROLL_end_end_angle_deg:48 -------------------------------------------------------------------------------- 2025-07-01T18:50:53 ROLL_start_start_angle_deg:48 -------------------------------------------------------------------------------- 2025-07-01T19:40:53 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-01T23:17:48 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-02T00:07:48 ROLL_end_end_angle_deg:47 -------------------------------------------------------------------------------- 2025-07-02T03:39:30 ROLL_start_start_angle_deg:47 -------------------------------------------------------------------------------- 2025-07-02T04:29:30 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-02T08:54:10 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-02T09:44:10 ROLL_end_end_angle_deg:47 -------------------------------------------------------------------------------- 2025-07-02T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 83 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-02T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-02T12:10:42 offset_end = 45 Estimated Calibration duration = 0:09:01.600000 offset = 45 PROBLEM => Calib procedure ends at offset 45, not in [50,90] -------------------------------------------------------------------------------- 2025-07-02T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 14 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-02T16:15:50 ROLL_start_start_angle_deg:47 -------------------------------------------------------------------------------- 2025-07-02T17:05:50 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-02T23:17:21 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-03T00:07:21 ROLL_end_end_angle_deg:46 -------------------------------------------------------------------------------- 2025-07-03T03:39:01 ROLL_start_start_angle_deg:46 -------------------------------------------------------------------------------- 2025-07-03T04:29:01 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-03T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 83 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-03T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-03T12:10:42 offset_end = 45 Estimated Calibration duration = 0:09:01.600000 offset = 45 PROBLEM => Calib procedure ends at offset 45, not in [50,90] -------------------------------------------------------------------------------- 2025-07-03T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 14 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-03T13:13:31 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-03T14:03:31 ROLL_end_end_angle_deg:46 -------------------------------------------------------------------------------- 2025-07-03T20:20:01 ROLL_start_start_angle_deg:46 -------------------------------------------------------------------------------- 2025-07-03T21:10:01 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-04T05:54:11 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-04T06:44:11 ROLL_end_end_angle_deg:45 -------------------------------------------------------------------------------- 2025-07-04T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 83 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-04T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-04T12:10:42 offset_end = 45 Estimated Calibration duration = 0:09:01.600000 offset = 45 PROBLEM => Calib procedure ends at offset 45, not in [50,90] -------------------------------------------------------------------------------- 2025-07-04T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 14 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-04T16:15:49 ROLL_start_start_angle_deg:45 -------------------------------------------------------------------------------- 2025-07-04T17:05:49 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-04T23:16:20 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-05T00:06:20 ROLL_end_end_angle_deg:44 -------------------------------------------------------------------------------- 2025-07-05T08:19:16 ROLL_start_start_angle_deg:44 -------------------------------------------------------------------------------- 2025-07-05T09:09:16 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-05T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 83 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-05T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-05T12:10:42 offset_end = 45 Estimated Calibration duration = 0:09:01.600000 offset = 45 PROBLEM => Calib procedure ends at offset 45, not in [50,90] -------------------------------------------------------------------------------- 2025-07-05T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 14 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-05T12:59:58 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-05T13:49:58 ROLL_end_end_angle_deg:43 -------------------------------------------------------------------------------- 2025-07-05T18:19:55 ROLL_start_start_angle_deg:43 -------------------------------------------------------------------------------- 2025-07-05T19:09:55 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-06T04:28:34 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-06T05:18:34 ROLL_end_end_angle_deg:43 -------------------------------------------------------------------------------- 2025-07-06T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 83 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-06T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-06T12:10:42 offset_end = 45 Estimated Calibration duration = 0:09:01.600000 offset = 45 PROBLEM => Calib procedure ends at offset 45, not in [50,90] -------------------------------------------------------------------------------- 2025-07-06T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 14 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-06T19:11:05 ROLL_start_start_angle_deg:43 -------------------------------------------------------------------------------- 2025-07-06T20:01:05 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-06T21:52:50 AIAF063A Halt_science_on_PAS ------------------- 2025-07-06T21:47:53 SCET offset = 173 PROBLEM => Stop PAS science offset = 173.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-07-06T21:54:20 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-07-06T21:59:38 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-07-06T22:05:00 WOL_start -------------------------------------------------------------------------------- 2025-07-07T01:05:00 WOL_end