URL = https://mssl.ucl.ac.uk/missions/SolO/Webpages/weekly_ops_plans/SWA-operations-plan-for-LTP20-STP368-v01_early.html Start of STP368 is 2025-07-06T22:00:00Z DT = 2025-07-06T00:00:00.000 805075200.00 seconds since 2000-01-01 SCET = 1/0805074901:64088 805074901.98 SCET 298.02 seconds drift SCET DRIFT = 298.0220947265625 -------------------------------------------------------------------------------- 2025-07-06T22:05:00 WOL_start -------------------------------------------------------------------------------- 2025-07-07T01:05:00 WOL_end -------------------------------------------------------------------------------- 2025-07-07T02:05:04 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-07-07T02:05:08 AIAF100B Sensor_cadence (USE_EAS1_R, USE_EAS2_R, USE_PAS_R, IGNORE, HIGH_CADENCE, HIGH_CADENCE, HIGH_CADENCE, NOMINAL_CADENCE) ------------------- 2025-07-07T02:00:10 SCET offset = 10 -------------------------------------------------------------------------------- 2025-07-07T02:05:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 12 => OK (no check) -------------------------------------------------------------------------------- 2025-07-07T02:05:14 AIAF135A Configure_PAS_FS (0x00, 0x0A, 0x40, 0x00, 0x09, 0x01) -------------------------------------------------------------------------------- 2025-07-07T02:05:18 AIAF069A Configure_PAS_BM (0x00, 0x04, 0x5A, 0x00, 0x09, 0x24, 0x05, 0x04) -------------------------------------------------------------------------------- 2025-07-07T02:05:22 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-07-07T02:25:12 -------------------------------------------------------------------------------- 2025-07-07T02:23:44 ROLL_start_start_angle_deg:0 ERROR => PROBLEM : No PAS TC allowed before 2025-07-07T02:25:12 -------------------------------------------------------------------------------- 2025-07-07T02:28:22 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-07-07T02:30:17 AIAF061A Start_PAS_science ------------------- 2025-07-07T02:25:19 SCET offset = 19 PROBLEM => Start science offset 19 not in [20,90] or [120,190] -------------------------------------------------------------------------------- 2025-07-07T02:31:17 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-07-07T03:13:44 ROLL_end_end_angle_deg:42 -------------------------------------------------------------------------------- 2025-07-07T12:00:50 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 52 => OK (no check) -------------------------------------------------------------------------------- 2025-07-07T12:02:10 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-07T12:11:11 offset_end = 73 Estimated Calibration duration = 0:09:01.600000 offset = 73 => OK -------------------------------------------------------------------------------- 2025-07-07T12:12:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 42 => OK (no check) -------------------------------------------------------------------------------- 2025-07-07T12:50:15 ROLL_start_start_angle_deg:42 -------------------------------------------------------------------------------- 2025-07-07T13:40:15 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-08T04:29:54 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-08T05:19:54 ROLL_end_end_angle_deg:40 -------------------------------------------------------------------------------- 2025-07-08T12:00:50 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 52 => OK (no check) -------------------------------------------------------------------------------- 2025-07-08T12:02:10 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-08T12:11:11 offset_end = 73 Estimated Calibration duration = 0:09:01.600000 offset = 73 => OK -------------------------------------------------------------------------------- 2025-07-08T12:12:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 42 => OK (no check) -------------------------------------------------------------------------------- 2025-07-08T17:51:04 ROLL_start_start_angle_deg:40 -------------------------------------------------------------------------------- 2025-07-08T18:41:04 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-09T05:23:05 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-09T06:13:05 ROLL_end_end_angle_deg:39 -------------------------------------------------------------------------------- 2025-07-09T12:00:50 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 52 => OK (no check) -------------------------------------------------------------------------------- 2025-07-09T12:02:10 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-09T12:11:11 offset_end = 73 Estimated Calibration duration = 0:09:01.600000 offset = 73 => OK -------------------------------------------------------------------------------- 2025-07-09T12:12:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 42 => OK (no check) -------------------------------------------------------------------------------- 2025-07-09T12:44:31 ROLL_start_start_angle_deg:39 -------------------------------------------------------------------------------- 2025-07-09T13:34:31 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-09T16:03:37 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-09T16:53:37 ROLL_end_end_angle_deg:39 -------------------------------------------------------------------------------- 2025-07-09T20:25:02 ROLL_start_start_angle_deg:39 -------------------------------------------------------------------------------- 2025-07-09T21:15:02 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-10T11:54:52 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-10T12:00:50 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 52 => OK (no check) -------------------------------------------------------------------------------- 2025-07-10T12:02:10 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-10T12:11:11 offset_end = 73 Estimated Calibration duration = 0:09:01.600000 offset = 73 => OK -------------------------------------------------------------------------------- 2025-07-10T12:12:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 42 => OK (no check) -------------------------------------------------------------------------------- 2025-07-10T12:44:52 ROLL_end_end_angle_deg:38 -------------------------------------------------------------------------------- 2025-07-10T20:25:59 ROLL_start_start_angle_deg:38 -------------------------------------------------------------------------------- 2025-07-10T21:15:59 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-11T01:02:11 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-11T01:52:11 ROLL_end_end_angle_deg:37 -------------------------------------------------------------------------------- 2025-07-11T08:23:31 ROLL_start_start_angle_deg:37 -------------------------------------------------------------------------------- 2025-07-11T09:13:31 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-11T11:54:20 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-11T12:00:50 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 52 => OK (no check) -------------------------------------------------------------------------------- 2025-07-11T12:02:10 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-11T12:11:11 offset_end = 73 Estimated Calibration duration = 0:09:01.600000 offset = 73 => OK -------------------------------------------------------------------------------- 2025-07-11T12:12:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 42 => OK (no check) -------------------------------------------------------------------------------- 2025-07-11T12:44:20 ROLL_end_end_angle_deg:36 -------------------------------------------------------------------------------- 2025-07-11T16:15:40 ROLL_start_start_angle_deg:36 -------------------------------------------------------------------------------- 2025-07-11T17:05:40 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-12T04:32:58 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-12T05:22:58 ROLL_end_end_angle_deg:36 -------------------------------------------------------------------------------- 2025-07-12T12:00:50 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 52 => OK (no check) -------------------------------------------------------------------------------- 2025-07-12T12:02:10 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-12T12:11:11 offset_end = 73 Estimated Calibration duration = 0:09:01.600000 offset = 73 => OK -------------------------------------------------------------------------------- 2025-07-12T12:12:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 42 => OK (no check) -------------------------------------------------------------------------------- 2025-07-12T16:29:32 ROLL_start_start_angle_deg:36 -------------------------------------------------------------------------------- 2025-07-12T17:19:32 ROLL_end_end_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-12T23:11:11 ROLL_start_start_angle_deg:0 -------------------------------------------------------------------------------- 2025-07-13T00:01:11 ROLL_end_end_angle_deg:35 -------------------------------------------------------------------------------- 2025-07-13T01:23:50 AIAF063A Halt_science_on_PAS ------------------- 2025-07-13T01:18:52 SCET offset = 232 PROBLEM => Stop PAS science offset = 232.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-07-13T01:23:58 AIAF133A Abort_the_PAS_sequencer ------------------- 2025-07-13T01:19:00 SCET offset = 240 -------------------------------------------------------------------------------- 2025-07-13T01:24:14 AIAF113A Disable_SAF_response_for_EAS_and_PAS (SASTEERING_MI) -------------------------------------------------------------------------------- 2025-07-13T01:24:18 MAINT_start_type:SA_RELUBRICATION -------------------------------------------------------------------------------- 2025-07-13T01:34:18 MAINT_end_type:SA_RELUBRICATION -------------------------------------------------------------------------------- 2025-07-13T01:34:24 AIAF112A Enable_SAF_response_for_EAS_and_PAS (SASTEERING_MI) -------------------------------------------------------------------------------- 2025-07-13T01:34:42 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 84 => OK (no check) -------------------------------------------------------------------------------- 2025-07-13T01:35:22 AIAF061A Start_PAS_science ------------------- 2025-07-13T01:30:24 SCET offset = 24 => OK -------------------------------------------------------------------------------- 2025-07-13T01:35:42 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 44 => OK (no check) -------------------------------------------------------------------------------- 2025-07-13T12:00:50 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 52 => OK (no check) -------------------------------------------------------------------------------- 2025-07-13T12:02:10 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-13T12:11:11 offset_end = 73 Estimated Calibration duration = 0:09:01.600000 offset = 73 => OK -------------------------------------------------------------------------------- 2025-07-13T12:12:20 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 42 => OK (no check) -------------------------------------------------------------------------------- 2025-07-13T22:46:36 AIAF063A Halt_science_on_PAS ------------------- 2025-07-13T22:41:38 SCET offset = 98 PROBLEM => Stop PAS science offset = 98.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-07-13T22:48:14 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-07-13T22:54:56 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-07-14T00:11:00 WOL_start -------------------------------------------------------------------------------- 2025-07-14T03:11:00 WOL_end