URL = https://mssl.ucl.ac.uk/missions/SolO/Webpages/weekly_ops_plans/SWA-operations-plan-for-LTP20-STP371-v01_early.html Start of STP371 is 2025-07-28T00:00:00Z DT = 2025-07-28T00:00:00.000 806976000.00 seconds since 2000-01-01 SCET = 1/0806975698:30966 806975698.47 SCET 301.53 seconds drift SCET DRIFT = 301.5274963378906 -------------------------------------------------------------------------------- 2025-07-28T00:05:00 WOL_start -------------------------------------------------------------------------------- 2025-07-28T03:05:00 WOL_end -------------------------------------------------------------------------------- 2025-07-28T04:05:04 AIAF112A Enable_TFF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-07-28T04:05:08 AIAF100B Sensor_cadence (USE_EAS1_R, USE_EAS2_R, USE_PAS_R, IGNORE, HIGH_CADENCE, HIGH_CADENCE, HIGH_CADENCE, NOMINAL_CADENCE) ------------------- 2025-07-28T04:00:07 SCET offset = 7 -------------------------------------------------------------------------------- 2025-07-28T04:05:10 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 9 => OK (no check) -------------------------------------------------------------------------------- 2025-07-28T04:05:14 AIAF135A Configure_PAS_FS (0x00, 0x0A, 0x40, 0x00, 0x09, 0x01) -------------------------------------------------------------------------------- 2025-07-28T04:05:18 AIAF069A Configure_PAS_BM (0x00, 0x04, 0x5A, 0x00, 0x09, 0x24, 0x05, 0x04) -------------------------------------------------------------------------------- 2025-07-28T04:05:22 AIAF066A Recover_PAS_HVs (0x0613) Need to wait 00:19:50 until 2025-07-28T04:25:12 -------------------------------------------------------------------------------- 2025-07-28T04:28:22 AIAF066B Enable_last_of_PAS_FDIR_monitors -------------------------------------------------------------------------------- 2025-07-28T04:30:17 AIAF061A Start_PAS_science ------------------- 2025-07-28T04:25:16 SCET offset = 16 PROBLEM => Start science offset 16 not in [20,90] or [120,190] -------------------------------------------------------------------------------- 2025-07-28T04:31:17 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 76 => OK (no check) -------------------------------------------------------------------------------- 2025-07-28T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-07-28T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-28T12:10:42 offset_end = 41 Estimated Calibration duration = 0:09:01.600000 offset = 41 PROBLEM => Calib procedure ends at offset 41, not in [50,90] -------------------------------------------------------------------------------- 2025-07-28T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 10 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-29T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-07-29T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-29T12:10:42 offset_end = 41 Estimated Calibration duration = 0:09:01.600000 offset = 41 PROBLEM => Calib procedure ends at offset 41, not in [50,90] -------------------------------------------------------------------------------- 2025-07-29T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 10 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-30T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-07-30T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-30T12:10:42 offset_end = 41 Estimated Calibration duration = 0:09:01.600000 offset = 41 PROBLEM => Calib procedure ends at offset 41, not in [50,90] -------------------------------------------------------------------------------- 2025-07-30T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 10 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-07-31T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-07-31T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-07-31T12:10:42 offset_end = 41 Estimated Calibration duration = 0:09:01.600000 offset = 41 PROBLEM => Calib procedure ends at offset 41, not in [50,90] -------------------------------------------------------------------------------- 2025-07-31T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 10 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-08-01T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-08-01T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-08-01T12:10:42 offset_end = 41 Estimated Calibration duration = 0:09:01.600000 offset = 41 PROBLEM => Calib procedure ends at offset 41, not in [50,90] -------------------------------------------------------------------------------- 2025-08-01T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 10 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-08-02T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-08-02T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-08-02T12:10:42 offset_end = 41 Estimated Calibration duration = 0:09:01.600000 offset = 41 PROBLEM => Calib procedure ends at offset 41, not in [50,90] -------------------------------------------------------------------------------- 2025-08-02T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 10 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-08-02T13:02:04 AIAF063A Halt_science_on_PAS ------------------- 2025-08-02T12:57:03 SCET offset = 123 PROBLEM => Stop PAS science offset = 123.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-08-02T13:02:12 AIAF133A Abort_the_PAS_sequencer ------------------- 2025-08-02T12:57:11 SCET offset = 131 -------------------------------------------------------------------------------- 2025-08-02T13:02:28 AIAF113A Disable_SAF_response_for_EAS_and_PAS (SASTEERING_MI) -------------------------------------------------------------------------------- 2025-08-02T13:02:32 SA_ROT_start -------------------------------------------------------------------------------- 2025-08-02T13:22:32 SA_ROT_end -------------------------------------------------------------------------------- 2025-08-02T13:22:38 AIAF112A Enable_SAF_response_for_EAS_and_PAS (SASTEERING_MI) -------------------------------------------------------------------------------- 2025-08-02T13:22:56 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 75 => OK (no check) -------------------------------------------------------------------------------- 2025-08-02T13:23:36 AIAF061A Start_PAS_science ------------------- 2025-08-02T13:18:35 SCET offset = 215 PROBLEM => Start science offset 215 not in [20,90] or [120,190] -------------------------------------------------------------------------------- 2025-08-02T13:23:56 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 35 => OK (no check) -------------------------------------------------------------------------------- 2025-08-03T11:59:40 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x01) offset_100 = 79 => OK (no check) -------------------------------------------------------------------------------- 2025-08-03T12:01:41 AIAF067A Start_PAS_Calibration (0x03D6, 0x075B, 0x0613) Need to wait 00:09:01 until 2025-08-03T12:10:42 offset_end = 41 Estimated Calibration duration = 0:09:01.600000 offset = 41 PROBLEM => Calib procedure ends at offset 41, not in [50,90] -------------------------------------------------------------------------------- 2025-08-03T12:11:51 AIAF068A Configure_PAS_NM (0x00, 0x14, 0x40, 0x01, 0x07, 0x01, 0x5D) offset_100 = 10 PROBLEM => offset_100 not in [20,80] -------------------------------------------------------------------------------- 2025-08-03T19:52:50 AIAF063A Halt_science_on_PAS ------------------- 2025-08-03T19:47:49 SCET offset = 169 PROBLEM => Stop PAS science offset = 169.0 : should be in [135, 145] -------------------------------------------------------------------------------- 2025-08-03T19:54:20 AIAF065A Safe_PAS_HVs (0x0613) -------------------------------------------------------------------------------- 2025-08-03T19:59:38 AIAF113A Disable_TTF_response_for_EAS_and_PAS -------------------------------------------------------------------------------- 2025-08-03T20:05:00 WOL_start -------------------------------------------------------------------------------- 2025-08-03T23:05:00 WOL_end